Heavy Duty Pedal Kit

Kit includes: Gas and Brake pedals Gas and brake pedal springs 2 Pedal Stops 2 1" Shoulder Bolts and Nuts

Pedal Stops

2" long 1.5" wide 1" deep 1.25" center Comes as a pair.

Springer Spindle Bracket Kit Pair

Works with all DIY go kart kits and 10548 / 10549  and 13788/13789 spindles. 10548 /10549 - 5" long 13788 / 13789 - 5 1/2" long 1.25" wide 1/2" kingpin hole 1/4" thick 4.5" inside opening Includes: 2 Brackets 2 2 1/4" Springs 2 ...

Steering Wheel Washer

2 1/2" OD 3/16" Thick 3/4" Center Hole Bolt Circle 1 3/8"

Pitman Arm for Steering Shaft

4" Length 3/8" Hole 3/16" Thick 3/4" Wide

1" Bore Hub with 1/4" Keyway

OD 1.876  Machined Lip 1.678 comes with 2 set screws

Predator Engine Mount 2 ( 420cc/670cc)

6 3/4" x 16" 3 5/8" by 3/8" mounting slots.   1" 90 degree bend along the length on each side. Made from 1/4" (.250") steel plate Works with 420cc and 670cc Predator engines

Spindle Arm

4 1/4" long 1" wide 3/8" diameter hole

Pitman Steering Arm

5/8" steering shaft hole,   5/16" tie rod bolt hole,   1-3/4" between holes center to center.   Made in the USA by AZUSA.

Engine Mount (212cc / 225cc/ 301cc)

5 1/2" wide x 14" long 3" by 3/8" mounting slots.   1" 90 degree bend along the length on each side. Made from 3/16 material  Works with 212cc, 225 and 301cc Tillotson and Predator engines. Please use 5/16" bolts with washers to mount.

3" X 3" Gusset

11 Gauge thick steel Actual size is 2 7/8" x 2 7/8".

3" X 3.5" Gusset

11 Gauge thick steel Actual size is 3 1/2" x 2 7/8".

2" X 2" Gusset

11 Gauge thick steel Actual size is 1 3/4" x 1 3/4".

Two Seat Side Restraints 12"

  This is for 2 Side Restraints 5-7/8" tall 12" wide 1" tubular steel

Two Seat Side Restraints 20"

Side seat restaints. This is for two side rails 7.5" tall angled down to 6.5" 20" wide 1" tubular steel

Seat Back / Front Bumper

Can be used for either the front bumper or as the seat back. 12" tall 24" wide 1" tubular steel

Steering Hoop / Engine Guard

Can be used for either the steering hoop or as an engine guard. 16" Tall 5" Outside Dimension 1" Tubular Steel

Jackshaft Bearing Washer

Weld-on washer to make your own jackshaft set-up. Used with bearing OD of  1 3/8".

Engine Mount Short, Small Block

Engine mount, flat plate with elongated holes. For 3-7 hp engines Dimensions- 11 Gauge material 12" Long 5" wide

Bearing Hanger (One Hanger)

Bearing hangers, priced each. 2 needed per axle.  Hangers are 4" wide and 3 5/8" tall.   Works with both 2 hole and 3 hole flanges.