Weld-Ons

7/8" Hex Hub

7/8" ID Steel Hex Hub with step down and set screw. 1-13/16" Overall Width 1.5" Deep  

3.5" Hub Flange

Weld up your own custom hubs with this 3.5" diameter hub flange made out of 3/16" mild steel. Dimensions: OD - 3.500" ID - 1.630" 3 hole pattern - 2.500" bolt circle

6" Hub Flange, Dual Pattern

Weld up your own custom hubs with this 6" diameter hub flange made out of 3/16" mild steel. Dimensions: OD - 6" ID - 1.630" 4 hole pattern - 2.875" 6 hole pattern - 5.250"

Adjustable Jackshaft Brackets, Weld-On

Weld on adjustable jackshaft brackets made in the USA out of 3/16" steel. This is the perfect kit for a wide range of mini bikes to fine tune and easily change the gear ratio. Laser cut out of 3/16" steel Must be welded onto frame 5/16" bolts and...

Gusset, 5" Long, 45 Degree

Weld on gusset perfect for any 45 degree angle such as on the Mega Moto 80/105 mini bike. 11 gauge steel (.120" thick) 5.25" long 1.5" at widest point

Header Flange, 301cc/420cc

Steel Header Pipe Flange.  3/16" Thick. Fits: 301cc/420cc Predator Engines GX270-390 Hondas

Header Flange, 196cc/212cc

Steel Header Pipe Flange.  3/16" Thick. Fits: 79cc/196cc/212cc Honda and Honda Clones

Mikuni Throttle Cable Bracket

Works with the Mikuni throttle cable.

Pedal Stops

2" long 1.5" wide 1" deep 1.25" center Comes as a pair.

Springer Spindle Bracket Kit Pair

Works with all DIY go kart kits and 10548 / 10549  and 13788/13789 spindles. 10548 /10549 - 5" long 13788 / 13789 - 5 1/2" long 1.25" wide 1/2" kingpin hole 1/4" thick 4.5" inside opening Includes: 2 Brackets 2 2 1/4" Springs 2 ...

Steering Wheel Washer

2 1/2" OD 3/16" Thick 3/4" Center Hole Bolt Circle 1 3/8"

Pitman Arm for Steering Shaft

4" Length 3/8" Hole 3/16" Thick 3/4" Wide

1" Bore Hub with 1/4" Keyway

OD 1.876  Machined Lip 1.678 comes with 2 set screws

Predator Engine Mount 2 ( 420cc/670cc)

6 3/4" x 16" 3 5/8" by 3/8" mounting slots.   1" 90 degree bend along the length on each side. Made from 1/4" (.250") steel plate Works with 420cc and 670cc Predator engines

Spindle Arm

4 1/4" long 1" wide 3/8" diameter hole

Pitman Steering Arm

5/8" steering shaft hole,   5/16" tie rod bolt hole,   1-3/4" between holes center to center.   Made in the USA by AZUSA.

Engine Mount (212cc / 225cc/ 301cc)

5 1/2" wide x 14" long 3" by 3/8" mounting slots.   1" 90 degree bend along the length on each side. Made from 3/16 material  Works with 212cc, 225 and 301cc Tillotson and Predator engines. Please use 5/16" bolts with washers to mount.

3" X 3" Gusset

11 Gauge thick steel Actual size is 2 7/8" x 2 7/8".

3" X 3.5" Gusset

11 Gauge thick steel Actual size is 3 1/2" x 2 7/8".

2" X 2" Gusset

11 Gauge thick steel Actual size is 1 3/4" x 1 3/4".